1. Corrosion Protection

• Inspect: Sacrificial anodes on the motor, trim tabs, and hull.
• Replace: Any anode with < 50% material remaining.
• Choose material: Aluminum vs. zinc anodes — which suits your water.
• Pro tip: Clean mounting points so the anode makes bare-metal contact.

Shop Zinc & Aluminum Anodes

2. Trailer Check

• Inspect: Bunk slides, guide posts, step pads, winch strap, and safety chains.
• Replace: Cracked bunks/pads; tires past service life or with low tread/uneven wear.
• Test: Lights and wiring; clean/secure grounds to prevent spring gremlins.
• Pro tip: Fix it now—it’s easier than at the ramp on opening day.

Shop Trailer Parts

3. Water & Drainage

• Flush: Livewell and deck drains to clear debris before storage.
• Replace: Worn deck drains, scuppers, and scupper flaps that stick or leak.
• Inspect: Hoses & clamps for cracks or drips; tighten or swap as needed.
• Seal up: Address missing/broken seals—rub rail, windshield, deck, hatch & door.

Shop Water & Drainage

4. Plumbing & Fills

• Inspect: Through-hulls, deck drains, deck fills, and drain plugs—everything tight & sealed.
• Replace: Deck fills with cracked caps or corroded flanges; renew O-rings.
• Service: Verify drain plugs and spares are in good shape and labeled.
• Check: Fuel vent/overflow fittings and screens for salt or insect debris.

Shop Plumbing & Fills

5. Latches, Hinges, & Hardware

• Inspect: Hinges, latches, and gas shocks—replace anything rusted, bent, or loose.
• Service: Clean & lube sliding door tracks, trucks, and wheels.
• Replace: Missing cabin door keys, worn strikers, or tired door holders.
• Off-season tip: Plan measurements for BYO doors & hatches so spring installs are plug-and-play.

Shop Replacement Hardware

6. Deck Hardware & Line Protection

• Inspect: Cleats, hawse pipes, and deck plates for corrosion or burrs that could chafe lines.
• Replace/Upgrade: Pitted hardware or sharp-edged fairleads; smooth burrs to protect rope.
• Check: Anchor locker rollers and chafe points; add guards where needed.
• Service note: Drain/air-purge any transom shower or washdown lines per your boat manual.

Shop Deck Hardware

1. Corrosion Protection

• Inspect: Sacrificial anodes on the motor, trim tabs, and hull.
• Replace: Any anode with < 50% material remaining.
• Choose material: Aluminum vs. zinc anodes — which suits your water.
• Pro tip: Clean mounting points so the anode makes bare-metal contact.

Shop Zinc & Aluminum Anodes

2. Trailer Check

• Inspect: Bunk slides, guide posts, step pads, winch strap, and safety chains.
• Replace: Cracked bunks/pads; tires past service life or with low tread/uneven wear.
• Test: Lights and wiring; clean/secure grounds to prevent spring gremlins.
• Pro tip: Fix it now—it’s easier than at the ramp on opening day.

Shop Trailer Parts

3. Water & Drainage

• Flush: Livewell and deck drains to clear debris before storage.
• Replace: Worn deck drains, scuppers, and scupper flaps that stick or leak.
• Inspect: Hoses & clamps for cracks or drips; tighten or swap as needed.
• Seal up: Address missing/broken seals—rub rail, windshield, deck, hatch & door.

Shop Water & Drainage

4. Plumbing & Fills

• Inspect: Through-hulls, deck drains, deck fills, and drain plugs—everything tight & sealed.
• Replace: Deck fills with cracked caps or corroded flanges; renew O-rings.
• Service: Verify drain plugs and spares are in good shape and labeled.
• Check: Fuel vent/overflow fittings and screens for salt or insect debris.

Shop Plumbing & Fills

5. Latches, Hinges, & Hardware

• Inspect: Hinges, latches, and gas shocks—replace anything rusted, bent, or loose.
• Service: Clean & lube sliding door tracks, trucks, and wheels.
• Replace: Missing cabin door keys, worn strikers, or tired door holders.
• Off-season tip: Plan measurements for BYO doors & hatches so spring installs are plug-and-play.

Shop Replacement Hardware

6. Deck Hardware & Line Protection

• Inspect: Cleats, hawse pipes, and deck plates for corrosion or burrs that could chafe lines.
• Replace/Upgrade: Pitted hardware or sharp-edged fairleads; smooth burrs to protect rope.
• Check: Anchor locker rollers and chafe points; add guards where needed.
• Service note: Drain/air-purge any transom shower or washdown lines per your boat manual.

Shop Deck Hardware

7. Pumps & Maintenance

• Inspect: Bilge, livewell, macerator, and washdown pumps for corrosion, leaks, or busted impellers.
• Flush: Run clean, fresh water through all pumps and hoses to remove salt, debris, and buildup.
• Replace: Any pump with damaged wiring, cracked housings, or weak motor output.
• Service tip: Label wiring and hoses now — it’ll save confusion when reconnecting in spring.

Shop Marine Pumps

8. Storage & Cleaning

• Clean: Wash decks, lockers, and hardware with marine-safe cleaner to remove salt, grime, and mildew.
• Wrap: Cover the boat with shrink wrap or a fitted cover, adding vents to prevent trapped moisture.
• Support: Position stands and pads evenly, chaining and leveling them before long-term storage.
• Replace: Torn wrap, missing vents, or cracked stand pads — swap before winter weather hits.

Shop Storage & Cleaning